BarFly 200 Highlights

• 2-Lamp remote fixture
• Fixture includes 90° Honeycomb Louver, Gel Frame and built-in head extension
• Same fixture takes daylight and tungsten lamps
• Mounts to stand
• Removable center-mount
• Fixture runs up to 75 feet (24 meters) from ballast
• Uses True Match® 3200K tungten balanced, 5500K daylight balanced and
  Visual Effects 420nm Blue and 550nm Green Lamps
  
• High-output, flicker-free ballast
• Instant-on, dead quiet
• Individual lamp switching – no color shift
• HO/Std switching
• Operates at 1/10th the power of conventional tungsten softlights
• UL listed, CE approved

BarFly 200 System

The first thing to note about the BarFly 200 System is that it consists of three components:
BarFly Fixture w/ 12ft (3.6m) head extension (fig. 1), Mounting Plate (fig. 2) and Ballast (fig. 3). 
It was designed in this manner to allow the greatest flexibility when working on film production where the
gaffer and DP are constantly being challenged to light unique locations and problem solve at a moment's notice.

The BarFly is most at home on location and studio sets for television and feature film production,
but many in the electronic field production and ENG community have discovered it for a small, two point or
three point lighting kit to complement such popular location lighting instruments as the Kino Flo Diva-Lites. 

BarFly 200 System

BarFly 200 Kits

The BarFly 200 Fixture

    

             BarFly 200 Fixture                               

The BarFly 200 Fixture houses the lamps and is comprised of a sturdy alloyed fixture, Gel Frame, removable 90° Honeycomb Louver with built-in Reflector and built-in head extension.

The BarFly 200 is only 2" deep and 9 1/2" wide, and 16" long. At six feet the BarFly 200 puts out about the same amount of light as a 500W softlight, and draws only two Amps of power.

Inserting Lamps

Insert lamps at a 45 degree angle and align pins with lamp holder.  Press lamp securely into lamp clip.

The BarFly 200 Ballast

  
          BAL-207-G120

All the features of the BarFly 200 fixture would be useless if Kino Flo had not developed its own
ballast that could run the fixture head remotely.  Unlike conventional architectural ballasts that need to operate three feet to six feet from the fixture head, Kino Flo ballasts can operate the fixture heads from up to 75 feet (3 x 25ft) extension cables.

The BarFly 200 Ballast is a high output, high frequency electronic ballast that can operate lamps up to 75 feet between ballast and fixture.  The ballast sends a high output current to the lamps to drive the light as brightly as possible.  Its high frequency electronics prevent any type of flicker as well.  A special heat-sink design and custom electronic engineering ensure stable operation without magnetic hum or cooling fans to interfere with the sound recording on set.

       BarFly 200 Ballast detail

There is no delay when switching lamps. The ballast operates the lights on/off instantly.  There is also a special Select switch to raise or drop the wattage in the tubes for light output and color control.  Keeping
the ballast remote from the fixture and lamps makes the controls more accessible to lighting crews who might need to rig the fixtures into set designs or high up in a lighting grid, but switch them easily from a convenient location on the stage floor.

The Kino Flo BarFly 200 ballast accomplishes all this and still out performs tungsten lighting instruments
10 to 1 when it comes to energy efficiency.  In other words, the BarFly ballast uses 1/10th as much power
to produce the same amount of soft light as incandescents.  The ballast works reliably under most normal conditions, but it’s also trustworthy in more harsh conditions, such as extreme cold. The BarFly ballast series
is designed to operate at temperatures from 14F to 122F (-10C to +50C).

In extremely cold temperatures, the ballast may not strike the lamps initially because the lamps may need to warm up.  Switch the ballast to Off, wait seven seconds and try again.  If the ballast does not strike after
two or three attempts, turn off the ballast, check that the extension and harness connections are secure and re-strike.  Once operating for a few minutes, the lamps should re-strike instantly.

The BarFly 200 Extension Cable

 
                      X09-G225

Up to 75 feet (3 x 25ft) of extension cable can be used between the fixture and the ballast.